| Full Width Pickup |
 |
Thorough field clearance.
Performance from the start: 83" (2.10 m) working width and suspended feeler wheels rake even the widest swaths clean and without any soiling of the fodder
|
 |
Perfect unity. The combination of double roller crop press and integrated baffle plate ensures an acceleration of crop flow and optimal compaction. This increases the intake capacity again. |
| Feeding System - ROTO CUT - 16 blades for a better and cleaner cut |
 |
Proven in the field
The 16-blade cutting rotor is geared for maximum throughput. The crop is fed accurately over the knife bed by the helical rotor blades, reaching a cutting frequency of over 8000 chops per minute, creating precision chopping and maximum throughput. The CLAAS stripper design keeps the area between and inside the tine blades clean and thus ensures maximum operating reliability in all grass harvesting conditions.
|
 |
ROTO REVERSE – the built-in reversing unit
The reverser is powered hydraulically and comes into its own in non-stop operation at the output limit. If a blockage occurs, the driver can quickly reverse the rotor from the cab and clear the obstruction. The stripper is protected by a lock that reverses in 90° steps.
|
| Baling Chamber - produces rock hard bales |
 |
Rugged design equals reliability
Silage baling is particularly demanding on the baler. The forage has to be compressed into highly dense packages at top speed. The sixteen steel roller design of the CLAAS baling chamber has proven to be the ideal design for achieving this objective. The ROLLANT system, with its freely rotating steel rollers and profiled surfaces, comes into its own in the damp and rough conditions typical of the silage harvest. The real strength of the CLAAS rollers is concealed inside: up to eight reinforcement plates for absolute reliability.
|
 |
MPS - The new generation
Revised for you - the new MPS (Maximum Pressure System). Due to the bow-shaped layout of the rollers, the bales rotate inside the baling chamber with a minimum of force application. The new MPS achieves higher bale density with less tractor power, as well as perfectly round, highly compacted and storable bales.
|
| Tying - automatic tying - best results every time |
 |
Twine or net – ROLLANT gives you the choice.
The ROLLATEX net wrapping system saves precious time as bale tying is fully automated and only takes a matter of seconds. The fully adjustable net guidance system allows the net to be applied tightly along the entire width of the bale, and firmly binds the edges as well.
|
 |
Variable number of turns
As different crops require different amounts of wrapping, you can set the number of turns over a wide range according to the task at hand.
|
 |
Economy version
Twine wrapping is the classic method used by many farms. Twine is even cheaper than net. Up to 12 rolls of twine can be stored on the ROLLANT - enough wrapping material for a long working day.
|
| Bale Transfer |
 |
Efficient bale transfer
The UNIWRAP baler / wrapper combination is a compact unit allowing for the rapid and reliable transfer of the bale from front to back. The bale is transferred to the wrapper without touching the ground using an articulating transfer arm. Laterally mounted plates centre the bale accurately at this stage, even on sloping fields. The transfer arm then raises the bale onto the wrapping table, where it is guided by four large rollers.
|
| Wrapping Unit - for maximum wrapping performance |
 |
The CLAAS high performance wrapper unit covers the bale with six layers of stretch film in just 35 seconds. After this very brief wrapping cycle, the wrapping table is lowered without stopping and then the bale is dropped gently onto the field. When crossing slopes, the bale can be dropped where convenient whilst the next bale is being made.
NEW: As an option, the film can now be prestretched by 82% so that it clings firmly to the bale. Optimum use is made of the adhesive qualities of the film to ensure that the bale is hermetically sealed.
|
 |
Unbeatable wrapping performance
CLAAS has designed the UNIWRAP with twin 29.5 inch (750 mm) wrapping arms. This enables the bale to be stretchwrapped with six layers of stretch film and a 52 % overlap in a mere 35 seconds. This high speed means that the wrapper always finishes its job before the next bale is ready. The ROLLANT can continue at full speed despite the wrapping process.
|
 |
Hillside operation
The bale is rotated gently on the wrapping table while the two wrapping arms circle the bale rapidly. This means that the bale is kept steady when crossing slopes and the film is applied evenly over the whole bale. With four lateral guide rollers and a large guide roller at the rear, the Profi wrapping table is designed for high performance operation with perfect functioning over hillsides
|
 |
BALE TWISTER
With the new bale twister, wrapped bales can be placed on their ends. This minimises the damage from hard stubble as the bale face have far more plastic. For transport the BALE TWISTER is simply raised hydraulically (option), so the overall length of the UNIWRAP remains the same during transportation on the road.
|
| Drives |
 |
On the ROLLANT, all rollers are driven. This means that even in the driest harvesting conditions, baling will not stop. The highest quality, reinforced roller chains guarantee complete operational safety. Optimal chain tension is guaranteed by self-adjusting, spring-loaded chain adjusters.
Lubrication equals smoother running
The drive chains are lubricated automatically. In addition to automatic chain adjustment, automatic lubrication contributes significantly to keeping wear and tear at a minimum. Use rapeseed oil for lubrication and protect the environment.
|
| Operation - professional control |
 |
Everything perfectly under control
ROLLANT 355 RC COMFORT and 355 RC UNIWRAP are equipped with the new CLAAS COMMUNICATOR. With its large display, the clearly laid-out terminal keeps you constantly informed about the machine’s operational status. What is more, you can access any of the five menus at all times and change the main set-up parameters very quickly using only one hand. Functions include binding, open tailgate, eject bales, close tailgate – the CLAAS COMMUNICATOR can manage all these processes.
|
 |
The CLAAS Medium Terminal
Changes of driver and changing harvesting conditions are the norm during harvesting periods. With the CLAAS Medium Terminal (CMT), you can program the baler according to the harvesting conditions prior to use. First, you can use the CMT to set all the main functions. Select the type of tying - net wrap or twine - and set the automatic tying start function to suit your requirements. You also have the option of initiating the tying operation manually, for example if swath is left over. Second, the CMT lets you control, with a very high level of precision, all the operations taking place behind the tractor during the baling and tying processes. Moreover, the terminal provides you with exact information on the number of bales made per day, the total number of bales and the aggregate time in hours. |
